Product outline
Torque, rotation speed and power are displayed
* Torque monitor specialized for UTMⅡ/UTMV
* Torque, rotation speed and power are displayed simultaneously
* Hold function
(Sample, Peak, Valley, P-P, Average)
* Upper/lower comparators function
(ALM HI, HI, OK, LO, ALM LO)
* Data storage function
* Easy connection to UTMⅡ/UTMV with one cable
* The unit supplies electric power to UTMⅡ/UTMV.
* Variation of torque, rpm, and power can be monitored and saved on PC. (with USB interface option only)
Specifications
Sensor input for torque|Drive power supply for UTMⅡ/UTMV|Pulse input for rotation speed|Display section|Setting section|External input/output section|General performance|Attachment
Sensor input for torque (voltage input) | |
Input resistance | 1MΩ |
---|---|
Signal input range | ±5V |
Accuracy |
Non-linearity:Within 0.02%/FS±1digit Zero drift:Within 0.2mV/℃ RTI Gain drift:Within 0.01%/℃ |
A/D converter |
・ Speed…300 times/sec. ・ Resolution…24bit(binary) Approx. 1/30000 with respect to 5V |
Analog filter | Low-pass filter(-6dB/oct) Selectable from 3, 30, 300, and 1kHz. |
Voltage output | Input voltage cuff (For test point) |
Drive power supply for UTMⅡ/UTMV | |
Power supply voltag | DC24V *One UTMⅡ/UTMV at the maximum |
---|
Pulse input for rotation speed (open collector input) | |
Maximum input frequency | In accordance with the output frequency of the UTMⅡ/UTMV series |
---|---|
Minimum input frequency |
Select from 15, 10, 5, 3, or 2 rpm (when pulse rate is 4 ppr) 60, 40, 20, 12, 8 rpm (when pulse rate is 1 ppr) |
Minimum detection pulse width | 50μs |
Circuit configuration |
No-voltage contact input (minus common) Open collector connectable(Ic=Approx. 10mA) |
Display section | |
Display |
Main display:Character height 15mm Numerical display by 7-segment green LED(5-digit+sign) Sub display :Character height 8mm Numerical display by 7-segment green LED(5-digit) |
---|---|
Indicated value |
Main display:5-digit -99999~+99999 Signs: Minus sign on most significant digit Sub display :5-digit -19999~+99999 Signs: Minus sign on most significant digit |
Decimal point | 0, 0.0, 0.00, 0.000(Only a torque and a power. Rotation speed is nothing) |
Display frequency | Selectable from 3, 6, 13, and 25 times/sec. |
Status display | HI/LO/HOLD |
Setting section | |
Setting item |
HI/LO limit: HI limit /LO limit/Alarm HI limit/Alarm LO limit Comparison/hold: Comparison function select/Near zero/Hysteresis/Hold function select/Detection time/Average sample number/Hold start level Operation 1: Motion detect (time)/Motion detect (range)/Zero tracking (time)/Zero tracking (range)/SI/F function select/Display frequency/Display ON/OFF Operation 2: Digital filter (torque)/Analog filter (torque)/Dead band/Digital filter (rotation speed) Calibration: Calibration function select 1(torque)/Zero calibration/Equivalent input calibration/Actual load calibration/Digital offset/Digital Zero limit/Calibration function select 2 (rotation speed/ power) Protect/Initializ: Setting protect/Key protect/Initialize/Password/Record data clear |
---|---|
Hold |
Sample, Peak, Valley, P-P, Average Hold section setting (All section・External signal・External signal + Time・Level + Time) |
External input/output section | |
External input (4) |
Hold control/Hold reset/Digital Zero/Record data clear Dry contact input circuit (minus common type), Ic=10mA or less |
---|---|
External output (7) |
HI/LO limit comparison(alarm HI・HI・OK・LO・alarm LO) /Hold complete/RUN Open collector output circuit (sink type), Vceo=30V(max) Ic=30mA(max) |
Interface |
*Only one option can be installed. |
General performance | |
Power supply voltage | AC100V~240V(+10%-15%)(free power source) 50/60Hz |
---|---|
Power consumption | 14W max |
Operating conditions |
Operation:-10~+40℃ Storage-40~+80℃ Humidity:85%RH or less(non-condensing) |
Dimension | 96(W)×96(H)×138(D) mm(Projections excluded) |
Panel cutout size | 92×92(+1-0)mm |
Weight | Approx. 1.0kg |
Attachment | |
External input/output connector ×1 AC input cord 3m(with solderless terminal)* ×1 Cable for UTMⅡ/UTMV connection 2m ×1 Unit seal ×1 Connector for BCD output(with BCD output option) ×1 Operating tool(with D/A converter(3ch) option) ×1 Mini screwdriver(with D/A converter option) ×1 Operation manual ×1 *The attached AC input cord is intended for 100V AC power in Japan. |
Option
Model | Description |
BCO | BCD parallel data output interface |
---|---|
232 | RS-232C communication interface |
D3V | D/A converter voltage output(3ch) |
DAV | D/A converter voltage output |
DAI | D/A converter current output |
USB | USB interface |
Optional accessories
Model | Description |
CA372-I/O | Cable with FCN connector at one-end 3m |
---|---|
CAAC2P-B3 | AC Supply cord 3m |
CAAC3P-CEE7/7-B2 | AC Supply cord (Voltage resistance:250V)2m |
CN34 | D-Sub9p connector for RS-232C |
CN50 | FCN series I/O connector (with cover) |
CN51 | BCD output connector |
CN55 | FCN series I/O connector (with diagonal cover) |
CN73 | D/A converter(3ch) connector |
CN90 | Waterproof plastic connector for UTMⅡ/UTMV connection |
DTC2-PSL | Case for TM301 |
咨询 - TM301