iMS Motionet Sdn Bhd
26, Jalan IKS Simpang Empat,
Taman IKS Simpang Empat,
14100 Simpang Ampat,
Penang, Malaysia.
26, Jalan IKS Simpang Empat,
Taman IKS Simpang Empat,
14100 Simpang Ampat,
Penang, Malaysia.
+604-5026180
Hotline: 1700 81 8880
Hotline: 1700 81 8880
+604-5025180
+60164015718
F741-C
Previous | 5 / 24 | Next |
RM 0.00
F741-C
Weighing Indicator for PROFIBUS

Product outline

Compatible with a fieldbus (PROFIBUS), and serial and analog outputs, it can be combined with a wide variety of plant devices.
The F741-C is a high-noise-resistant weighing indicator by which stable indicated values can be obtained. Compatible with a fieldbus (PROFIBUS), and serial and analog outputs, it can be combined with a wide variety of plant devices.

Specifications
ANALOG SECTION£üSETTING SECTION£üINPUT/OUTPUT SECTION£üDISPLAY SECTION£üGENERAL SPECIFICATIONS£üACCESSORIES
ANALOG SECTION | |
Excitation voltage |
DC10V±5£¥¡¡Output current£ºwithin 120mA Remote sense type £¨Up to four 350Ω load cells can be connected in parallel.£© |
---|---|
Signal input range | £0.2¡«2.2mV/V |
Zero adjustment range |
0¡«2.0mV/V Automatic adjustment by digital operation |
Span adjustment range |
0.3¡«2.0mV/V Automatic adjustment by digital operation |
Minimum input sensitivity | 0.3μV/count |
Accuracy |
|
Analog filter | Bessel type low-pass filter (-12dB/oct) Cutoff frequency 2Hz |
A/D converter |
|
Minimum indication resolution | 1/10000 |
Secondary calibration | Equivalent input calibration |
Minimum indication resolution for secondary calibration | 1/1000(ordinary temperature) |
SETTING SECTION | |
Setting method |
"Settings are made by operating the membrane keys. Also, settings can be made from a host computer through the RS-232C interface." |
---|---|
Memory of set values | NOV RAM (nonvolatile RAM) |
Setting item |
・Upper/lower Limit Comparison mode£ºUpper Limit / Lower Limit / Hold time / Near Zero / Tare setting / Tare display ・Over/Under Comparison Mode£ºTarget value / Over / Under / Hold time / Near Zero / Tare setting / Tare display ・Discharging control Mode£ºFinal / Compensation / Set point 1 /Comparison Inhibit Time / Judging Time / Complete Output Time / Near Zero / Tare setting / Tare display Password / Digital Filter / Motion Detection (Period)/ Motion Detection (Range) /Zero Tracking (Period) / Zero Tracking (Range) / Weighing Function 1 / Weighing Function 2 / Function key invalid・LOCK / Balance Weight Value / Capacity / Min. Scale Division / DZ Regulation Value / Display Selection / Gravitational Acceleration / Equivalent input calibration / Zero Calibration / Span Calibration / RS-232C I/F / D/A Output Mode / D/A zero Output / D/A Full Scale / PROFIBUS I/F /¡¡PROFIBUS Baud rate / Station No. |
INPUT/OUTPUT SECTION | |
Output signals(3points) |
HI£¯GO£¯LO£¨Can be changed to COMPL£¯SP2£¯SP1£© With short-circuit current limiting function by external power source. Transistor open collector output (Emitter = COM terminal) Output LO with transistor ON. |
---|---|
Input signals(1point) |
TARE ON when shorted with COM terminals by contact (relay, switch, etc.) or non-voltage-contact (transistor,TTL open-collector output, etc.) |
Interface |
|
DISPLAY SECTION | |
Numerical display tube | 14mm in character height¡¡Numerical display by 7-segment green LED (6 digits) |
---|---|
Indicated value | 6-digit, sign: negative display at the highest digit |
Display frequency | Select from 3, 6, 13 or 25 times/sec.(The system speed is 100 times/sec.) |
Unit | g, kg, t, lb, N, oz, and kN selectable (kg printed: Others are changed by the attached label.) |
Capacity | 5 digit |
Min. Scale Division | Setting allowable in the range of 1¡«100. |
Decimal point | Select from 0, 0.0, 0.00 or 0.000 (Zero blanking display by decimal point position) |
Over display |
|
Center zero | A true zero point or the center of each value is displayed. |
Status display | NZ£¯HOLD£¯ZALM£¯STAB£¯TARE£¯NET£¯CZ£¯HI£¯GO£¯LO£¯COMPL£¯SP2£¯SP1 |
GENERAL SPECIFICATIONS | |
Power supply voltage | AC100 ~ 240V (+10%, -15%) [free power source 50/60Hz] |
---|---|
Power consumption | Approx. 12W |
Rush current |
18A, 1.5mSec…100V AC mean load state (ordinary temperature, at cold-start time) 42A, 1.6mSec…240V AC mean load state(ordinary temperature, at cold-start time) |
Operating conditions |
Temperature: Operation£º£10¡«£«40¡æ ; Storage£º£20¡«£«85¡æ Humidity: 85%RH or less £¨non-condensing£© |
External dimensions | 144£¨W£©×72£¨H£©×160£¨D£©mm£¨Projections excluded£© |
Weight | Approx. 1.0kg |
ACCESSORIES | |
AC input cable (3 m) | 1 |
---|---|
Unit and status indication label | 1 |
Mini screwdriver for terminal block connection | 1 |
Jumper line | 2 |
Connector for D/A converter (with D/A converter option) | 1 |
Operation Manual | 1 |

Option
Model | Description |
PRF | PROFIBUS interface |
---|---|
DAC | D/A converter interface |

Optional accessories
Model | Description |
CAAC2P-B3 | AC input cord 3 m |
---|---|
CAAC3P-CEE7/7-B2 | AC input cord (withstand voltage: 250V) 2 m |
CN80 | Loadcell input connector terminal |
CN70 | D/A converter connector |
Our Agency Product Brands |