F701-P
Product outline
Practical unit that achieved functions and operability for weighing.
F701-P is a weighing indicator with convenient functions and operability for weighing such as a high-precision amplifier, fast-sampling, High-Low limit comparison function, weighing function and accumulation functions.
Specifications
Analog|Setting|External signal|Interface|Display|General specification|Attachment
Analog | |
Excitation voltage | DC5V±5% Output current:within 90mA Ratio metric type (Up to six 350Ω load cells can be connected in parallel.) |
---|---|
Signal input range | -0.5~3.0mV/V |
Zero adjustment range |
Automatic adjustment by digital operation -0.2~2.0mV/V |
Span adjustment range |
Automatic adjustment by digital operation |
Minimum input sensitivity | 0.15μV/count |
Accuracy |
|
A/D converter |
Conversion rate…300times/sec. Conversion resolution…24bit(binary) |
Minimum indication resolution | 1/10000 |
Setting | |
Setting method |
Settings are made by operating the membrane keys. Also, settings can be made from a host computer through the RS-485 interface. |
---|---|
Memory of set value | F-RAM (nonvolatile RAM) |
Protect of set value | Software LOCK can be set to parameter such as ''Set value'' and ''Calibration''. |
Setting item |
Upper limit/Lower limit/Near zero/Set point 1/Set point 2/Compensation/Over/Under/Final/Comparison inhibit time/Judging time/Complete output time/Weighing function 1/Weighing function 2/Tare setting/Tare display/Digital low pass filter/Moving average filter/Motion detection/Zero tracking (Period)/Zero tracking (Range)/Total comparison selection/Total limit (high 4 digit) /Total limit (under 5 digit) /Count limit/Key invalid/LOCK/Input selection/Output selection/Password/Balance weight value/Capacity/Min. scale division/DZ regulation value/Display selection/Gravitational acceleration/Zero calibration/Span calibration/RS-485 I/F setting/Communication type/RS-485 ID/Transmission delay time |
External signal (You can specify whether PNP (Source) type or NPN (Sink) type when order the F701-P.) | |
Output signals (4 points) |
Select from COMPL./SP1/SP2/SP3/HI/GO/LO/STAB/WEIGHT ERROR/TOTAL FINAL At signal ON, output transistor ON. ※External voltage must be prepared separately by customer. |
---|---|
Input signals (4 points) |
Select from G/N/D/Z ON/TARE ON/TARE OFF/ACCUMULATION CLEAR/HOLD/JUDGE Contact (relay, switch etc.) or non-contact (transistor, open collector etc.) can be connected. ※External voltage must be prepared separately by customer. |
Interface | |
RS-485 communication interface (Select from Modbus-RTU and original format) |
Display | |
Display |
18.5mm in character height, Numerical display on LCD(7 digit) Sub display:7.3mm in character height (14 digit) |
---|---|
Indicated value | 5 digit sign: negative display at the highest digit |
Accumulation value | 9 digit ※This can be changed to ''Accumulation count (4 digit)'' and ''Final(5 digit)''. |
Display frequency | Select from 1, 2, 5, 10, 20 times/sec.(The system speed is 300 times/sec.) |
Capacity | 5 digit |
Min. scale division | Setting allowable in the range of 1~50. |
Decimal point | Select from 0, 0.0, 0.00, 0.000 |
Over display |
LOAD:A/D converter input over, OFL1:Net Over, OFL2:Capacity + 9 scale division, OFL3:Gross Over |
Center zero | A true zero point or the center of each value is displayed. |
Status display |
COMPL./SP3/SP2/SP1/HI/GO/LO/ZT/ NZ/HOLD/ZALM/STAB/TARE/NET/GROSS/CZ |
General specification | |
Power supply voltage | AC100~240V(+10%-15%) (free power source 50/60Hz) |
---|---|
Power consumption | Approx. 5W |
Inrush current |
1.5A, 0.7mSec:AC100V average load condition (cold start at room temperature) 2.5A, 0.7mSec:AC200V average load condition (cold start at room temperature) |
Operating conditions |
Temperature…Operation -10℃~+40℃ Storage -20℃~+85℃ Humidity…85%RH or less (non-condensing) |
External dimensions | 192(W)×96(H)×102(D) mm (Projections excluded) |
Panel cutout dimensions |
186 +2 -0(W)×92 +1 -0(H)mm ※Installation panel thickness: 2.0~3.2mm |
Weight | Approx. 1.3kg |
Attachment | |
AC input cord (Nominal rating 125V) 3m | 1 |
---|---|
Jumper line | 2 |
Terminator | 1 |
Operation manual | 1 |
Rubber packing | 1 |
Optional accessories
Product | Description |
CN80 |
Loadcell input connector terminal (7P) |
---|
Inquiry - F701-P