AX40 - Ultra Precision

Category: Motorized Stages

Description

★Guide-Crossed-roller Guide, In structure, V-groove and crossed roller acquire movement in high accuracy and capacity by linear transmission to act a high precision movement and load capacity performance.
★Transmission Parts-Ball screw, It transmits through the ball involving in the locknut and screw to reach the accuracy and longer operation lifetime.
★Material-Aluminum Alloy

Model No.	Specification	Value
AX40-A2OP	Table Size (mm)	40 × 40
AX40-A2OP	Travel Stroke (mm)	15
AX40-A2OP	Drive Type	Ball Screw Ø6，lead 1mm
AX40-A2OP	Rail	Crossed-roller Bearing
AX40-A2OP	Stage Material / Surface Treatment	Aluminum Alloy / Black anodized
AX40-A2OP	Main Unit Weight (Kgs)	0.37
AX40-A2OP	Coupling	FAMMS12-3*5
AX40-A2OP	Accuracy Level	OP：Ultra Precision
AX40-A2OP	Wiring Method	R : Right wiring (Standard)；L : Left wiring
AX40-A2OP	Resolution(Pulse) (µm)	M: 2.5 (Full)；1.25 (Half) / J: 5 (Full)；2.5 (Half)
AX40-A2OP	Max. Speed(Full Step) (mm/sec)	10
AX40-A2OP	Positioning Precision (µm)	5
AX40-A2OP	Repeatability Precision(µm)	±0.3
AX40-A2OP	Load Capacity (Kgf)	6
AX40-A2OP	Missed Step (µm)	1
AX40-A2OP	Moment Stiffness	Pitch: 0.35 / Yaw: 0.45 / Rolling: 0.4 ("/N-cm)
AX40-A2OP	Pitch / Yaw	Pitch: < 25" / Yaw: < 20"
AX40-A2OP	Parallelism (µm)	30
AX40-A2OP	Dynamic Straightness (µm)	3
AX40-A2OP	Dynamic Parallelism (µm)	6.6
AX40-A2OP	Motor - Type / Shaft Numbers	M: 5-phase stepper high-resolution motor / ☐28 double shafts; J: 5-phase stepper motor / ☐28 double shafts
AX40-A2OP	Motor - Brand / Model	M: Orientalmotor / PK523HPMB; J: Orientalmotor / PKP523N12B
AX40-A2OP	Driver Brand / Model	Orientalmotor / CVD Series - 5 Phase stepping motor (Additional options)
AX40-A2OP	Stage Side Connector	15-Pin male end connetor D-SUB / 12-Pin male end connetor HRS
AX40-A2OP	Controller Side Connector	15-Pin female end connetor D-SUB (Additional options) / 12-Pin female end connetor HRS (Additional options)
AX40-A2OP	Origin Sensor	Photoelectric sensor GMT-sensor
AX40-A2OP	Limit Sensor	N/A
AX40-A2OP	Power Voltage	24V±10%
AX40-A2OP	Control Output	NPN open collector output under 24V 8mA
AX40-A2OP	Output Control	Testing (sensing)：output transistor OFF (closed)

Multi-point repeated positioning accuracy

♦ Accuracy measurement description

1. Unidirectional positioning accuracy: within the range of the predetermined detection stroke, starting from a starting position, moving and positioning in a certain direction sequentially, and detecting the actual
The difference between the movement value and the target movement value, and the maximum error value is taken. This value is the unidirectional positioning accuracy.
2. Multi-point repeated positioning accuracy: within the range of the predetermined detection stroke, when the mechanical program is executed, the position accuracy obtained by repeatedly running the same program code
degree. Calculate the position deviation that occurs when the same position is repeated back and forth, and obtain the deviation value between the two.

♦ Precision introduction

1. Design the GMT high-level precision inspection method to meet the precision requirements of fiber coupling and semiconductor manufacturing process.
2. The detection of GMT high-end precision linear slide module series adopts multi-point repeated measurement, that is, multi-point quantity measurement within a fixed stroke range (points
The amount is increased or decreased according to the length of the stroke), and the actual change of the round-trip position error is recorded, in pursuit of high precision and repeatability.
3. Through the non-contact laser interferometer measurement, to ensure that the unidirectional positioning is within 10μm, and the multipoint repetitive positioning accuracy is within 1.5μm. If there is a need for higher precision and precision, please contact the regional sales/business team.

System Configuration Diagram

♦ For detailed specifications, please read the description for the stage and connecting cable.

♦ For selection of driver, please refer to the cross-reference table for the motor/driver of the standard motorized stage or the GMT motor and driver catalog.

♦ The most preferred driver is recommended to be specified by GMT as considerations. For different needs, please choose the suitable driver based on real functional needs.