CZLC 60 - Ultra Precision

CZLC60

Table Size (mm)

60 × 60

CZLC60

Travel Stroke (mm)

30、50

CZLC60

Drive Type

Ball Screw Ø8，lead 1mm

CZLC60

Rail

Circular Linear Ball Guiding

CZLC60

Stage Material / Surface Treatment

Stainless Steel / Nickel plating

CZLC60

Accuracy Level

OP：Ultra Precision

CZLC60

Wiring Method

N：GMT Standard

CZLC60

Resolution(Pulse) (µm)

M: 1 (Full)；0.5 (Half) / J: 2 (Full)；1 (Half)

CZLC60

Max. Speed(Full Step) (mm/sec)

20

CZLC60

Positioning Precision (µm)

5

CZLC60

Repeatability Precision(µm)

±0.5

CZLC60

Multi-point Repeatability Precision(µm)

A: 1.5 / B: 1

CZLC60

Load Capacity (Kgf)

9

CZLC60

Missed Step (µm)

1

CZLC60

Parallelism (µm)

20

CZLC60

Dynamic Straightness (µm)

2

CZLC60

Dynamic Parallelism (µm)

10

CZLC60

Motor - Type / Shaft Numbers

M: 5-phase stepper high-resolution motor / ☐28 double shafts; J: 5-phase stepper motor / ☐28 double shafts

CZLC60

Motor - Brand / Model

M: Orientalmotor / PK523HPMB; J: Orientalmotor / PKP523N12B

CZLC60

Driver Brand / Model

Orientalmotor / CVD Series - 5 Phase stepping motor (Additional options)

CZLC60

Stage Side Connector

15-Pin male end connetor D-SUB / 12-Pin male end connetor HRS

CZLC60

Controller Side Connector

15-Pin female end connetor D-SUB (Additional options) / 12-Pin female end connetor HRS (Additional options)

CZLC60

Origin Sensor

Photoelectric sensor GMT-sensor

CZLC60

Limit Sensor

Origin Approximation Sensor

CZLC60

Limit Sensor

N / A

CZLC60

Power Voltage

24V±10%

CZLC60

Control Output

NPN open collector output under 24V 8mA

CZLC60

Output Control

Testing (sensing)：output transistor OFF (closed)

Multi-point repeated positioning accuracy

♦   Accuracy measurement description

1. Unidirectional positioning accuracy: within the range of the predetermined detection stroke, starting from a starting position, moving and positioning in a certain direction sequentially, and detecting the actual
The difference between the movement value and the target movement value, and the maximum error value is taken. This value is the unidirectional positioning accuracy.
2. Multi-point repeated positioning accuracy: within the range of the predetermined detection stroke, when the mechanical program is executed, the position accuracy obtained by repeatedly running the same program code
degree. Calculate the position deviation that occurs when the same position is repeated back and forth, and obtain the deviation value between the two.

♦   Precision introduction

1. Design the GMT high-level precision inspection method to meet the precision requirements of fiber coupling and semiconductor manufacturing process.
2. The detection of GMT high-end precision linear slide module series adopts multi-point repeated measurement, that is, multi-point quantity measurement within a fixed stroke range (points
The amount is increased or decreased according to the length of the stroke), and the actual change of the round-trip position error is recorded, in pursuit of high precision and repeatability.
3. Through the non-contact laser interferometer measurement, to ensure that the unidirectional positioning is within 10μm, and the multipoint repetitive positioning accuracy is within 1.5μm. If there is a need for higher precision and precision, please contact the regional sales/business team.

System Configuration Diagram

♦   For detailed specifications, please read the description for the stage and connecting cable.

♦   For selection of driver, please refer to the cross-reference table for the motor/driver of the standard motorized stage or the GMT motor and driver catalog.

♦   The most preferred driver is recommended to be specified by GMT as considerations. For different needs, please choose the suitable driver based on real functional needs.

Axis Definition

GMT has defined different axis as the following figuration according to the movement direction:

Horizontal movement direction is X and Y axis.

Vertical movement direction is Z axis.

Movement around X, Y, Z axis is defined to α axis, β axis, and θ axis.

Green arrows present the specified axis movement direction.