Product outline
By connecting UTMⅡ with the rotary encoder option, the relationship between torque and angle (or displacement/distance) change can be displayed in a graph (waveform), which in turn, is used for thorough waveform comparison.
There are two modes for waveform comparison useful for various purposes: “continuous” and “average” mode.
In “continuous mode,” HI and/or LO control outputs will be turned ON when the sensor input level goes over or below the high/low limit for predetermined number of times.
In “average mode,” a mean/average waveform data is calculated from a preset numbers of waveform data for OK/Not OK (NG) evaluation.
Features
■ Torque monitor for UTMⅡ/UTMV
■ Waveform display of torque variation against angles
■ Suitable for low-speed rotation and direct-acting applications
■ Hold function
■ Upper/lower limit of displacement against initial torque can be compared
■ Save measurement data and setting values in an SD card
■ Easy connection to UTMⅡ/UTMV with one cable
■ Operation power source can be supplied to the UTMⅡ/UTMV. (also to an optional rotary encoder)
Application example
<Screw driver with torque monitoring>
<Physical sensory test>
Specifications
Analog section|Display section|Setting section|External I/O signal|Interface|General performance|Attachments
Analog section | |
Torque input | -5 to +5V Input impedance:1MΩ or more |
---|---|
Accuracy |
Non-linearity : Within 0.02%FS±1digit Zero drift : Within 0.2mV/℃ RTI Gain drift : Within 0.01%/℃ |
Analog filter | Low pass filter (-6dB/oct.) Select from 30, 100, 300, 1kHz |
A/D converter |
・ Rate : 4000times/sec ・ Resolution : 24bit (binary) Approx. 1/30000 with respect to 5V |
Monitor output | Output level : Input voltage cuff (For test point) |
Pulse input (Open collector) |
Maximum input frequency : 50kHz Internal counting range : Approx. 1000000 |
Display section | |
Display unit | 3.5 inch TFT color LCD |
---|
Setting section | |
Setting method | Setting by analog type touch panel operation |
---|---|
Preservation of set values |
NOV RAM (nonvolatile RAM), Lithium-battery-backed-up C-MOS RAM |
External I/O signal | |
External output (15) | Hold result (Load, DPM)/Overload/Wave result/Complete/RUN/Load OK/DPM OK/SD OK |
---|---|
External input (12) | Load Digital Zero/DPM Positioning/Start/Stop/Hold/Reset/Backlight On/Prohibit Touch Panel/Work change |
Interface | |
Interface | RS-232C |
---|
General performance | |
Power supply | DC24V(±15%) |
---|---|
Power consumption | 7W typ. |
Operating conditions |
Temperature:Operation -10 to +40℃ Storage -20 to +60℃ Humidity:85%RH or less (non-condensing) |
Dimensions | 96(W)×96(H)×117.3(D)mm (Projections excluded) |
Weight | Approx. 1.0kg |
CE marking certification | EMC directives EN61326-1 |
Attachments | |
Operation manual・・・・・・1 External input/output connector・・・・・・1 Cable for UTMⅡ/UTMV connection (2m)・・・・・・1 Cable for UTMⅡrotary encoder connection (2m)・・・・・・1 SD card (1GB)(with SDC option)・・・・・・1 |
Product | Description |
SDC |
SD card slot (Approx. 80 waveforms can be preserved by 1MB, SDHC and SDXC are not supported.) All indicated values and all comparison waveforms can be saved and restored. Measured waveforms and judgment points can be saved automatically. |
---|
Product | Description |
DTC1 | Case for TM500 (with AC power supply) |
---|---|
SD1G | 1GByte card |
SD2G | 2GByte card |
CA81-232X | miniDIN-D-Sub9p cross cable 1.5m |
CATM21-M | Cable for UTMⅡ/UTMV connection 2m |
CATM51-M | Cable for UTMⅡ/UTMV connection 5m |
CATM(R)21-M | Cable for UTMⅡrotary encoder connection 2m |
CATM(R)51-M | Cable for UTMⅡrotary encoder connection 5m |
CN52 | FCN series I/O connector (with cover) |
CN57 | FCN series I/O connector (with diagonal cover) |
CN60 | Circular DIN 8p connector for RS-232C |
CN90 | Waterproof plastic connector for UTMⅡ/UTMV connection |
CN91 | Waterproof plastic connector for UTMⅡrotary encoder connection |
GMP96x96 | Rubber packing |
TSU03 | DC lighting surge unit |
Download
Product catalogue(PDF)
|
TM500 catalogue(594 KB) |
---|
Inquiry - TM500 (Torque Monitor)