|
Language: EN | 中文 |

Share:


TM301 (Torque Monitor)

Quantity: In Stock

Torque monitor for UTMⅡ/UTMV
 

Product outline

Torque, rotation speed and power are displayed

 

* Torque monitor specialized for UTMⅡ/UTMV
* Torque, rotation speed and power are displayed simultaneously
* Hold function
(Sample, Peak, Valley, P-P, Average)
* Upper/lower comparators function
(ALM HI, HI, OK, LO, ALM LO)
* Data storage function
* Easy connection to UTMⅡ/UTMV with one cable
* The unit supplies electric power to UTMⅡ/UTMV. 
* Variation of torque, rpm, and power can be monitored and saved on PC. (with USB interface option only)

Specifications

Sensor input for torque (voltage input)
Input resistance 1MΩ
Signal input range ±5V
Accuracy Non-linearity:Within 0.02%/FS±1digit
Zero drift:Within 0.2mV/℃ RTI
Gain drift:Within 0.01%/℃
A/D converter ・ Speed…300 times/sec.
・ Resolution…24bit(binary)  Approx. 1/30000 with respect to 5V
Analog filter Low-pass filter(-6dB/oct) Selectable from 3, 30, 300, and 1kHz.
Voltage output Input voltage cuff (For test point)
 
Drive power supply for UTMⅡ/UTMV
Power supply voltag DC24V *One UTMⅡ/UTMV at the maximum
 
Pulse input for rotation speed (open collector input)
Maximum input frequency In accordance with the output frequency of the UTMⅡ/UTMV series
Minimum input frequency Select from 15, 10, 5, 3, or 2 rpm (when pulse rate is 4 ppr) 
60, 40, 20, 12, 8 rpm (when pulse rate is 1 ppr)
Minimum detection pulse width 50μs
Circuit configuration No-voltage contact input (minus common)
Open collector connectable(Ic=Approx. 10mA)
 
Display section
Display Main display:Character height 15mm Numerical display by 7-segment green LED(5-digit+sign)
Sub display :Character height 8mm Numerical display by 7-segment green LED(5-digit)
Indicated value Main display:5-digit -99999~+99999 Signs: Minus sign on most significant digit
Sub display :5-digit -19999~+99999 Signs: Minus sign on most significant digit
Decimal point 0, 0.0, 0.00, 0.000(Only a torque and a power. Rotation speed is nothing)
Display frequency Selectable from 3, 6, 13, and 25 times/sec.
Status display HI/LO/HOLD
 
Setting section
Setting 
item
HI/LO limit:
HI limit /LO limit/Alarm HI limit/Alarm LO limit 

Comparison/hold:
Comparison function select/Near zero/Hysteresis/Hold function select/Detection time/Average sample number/Hold start level

Operation 1:
Motion detect (time)/Motion detect (range)/Zero tracking (time)/Zero tracking (range)/SI/F function select/Display frequency/Display ON/OFF

Operation 2:
Digital filter (torque)/Analog filter (torque)/Dead band/Digital filter (rotation speed)

Calibration:
Calibration function select 1(torque)/Zero calibration/Equivalent input calibration/Actual load calibration/Digital offset/Digital Zero limit/Calibration function select 2
(rotation speed/ power)

Protect/Initializ:
Setting protect/Key protect/Initialize/Password/Record data clear
Hold Sample, Peak, Valley, P-P, Average 
Hold section setting (All section・External signal・External signal + Time・Level + Time)
 
External input/output section
External input
(4)
Hold control/Hold reset/Digital Zero/Record data clear
Dry contact input circuit (minus common type), Ic=10mA or less
External output
(7)
HI/LO limit comparison(alarm HI・HI・OK・LO・alarm LO) /Hold complete/RUN
Open collector output circuit (sink type), Vceo=30V(max) Ic=30mA(max)
Interface
  • SIF:
  • 2-wire serial interface 
  •  
  • BCO:
  • BCD parallel data output interface (Option)
  •  
  • 232:
  • RS-232C communication interface (Option)
  •  
  • D3V:
  • D/A converter voltage output(3ch) (Option)
  •  
  • DAV:
  • D/A converter voltage output (Option)
  •  
  • DAI:
  • D/A converter current output (Option)
  • USB:
  • USB interface (Option)

 

*Only one option can be installed.

 
General performance
Power supply voltage AC100V~240V(+10%-15%)(free power source) 50/60Hz
Power consumption 14W max
Operating conditions Operation:-10~+40℃ Storage-40~+80℃
Humidity:85%RH or less(non-condensing)
Dimension 96(W)×96(H)×138(D) mm(Projections excluded)
Panel cutout size 92×92(+1-0)mm
Weight Approx. 1.0kg
 
Attachment
  External input/output connector ×1
AC input cord 3m(with solderless terminal)* ×1
Cable for UTMⅡ/UTMV connection 2m ×1
Unit seal ×1
Connector for BCD output(with BCD output option) ×1
Operating tool(with D/A converter(3ch) option) ×1
Mini screwdriver(with D/A converter option) ×1
Operation manual ×1
*The attached AC input cord is intended for 100V AC power in Japan.
 

 

 

Option

Model Description
BCO BCD parallel data output interface
232 RS-232C communication interface
D3V D/A converter voltage output(3ch)
DAV D/A converter voltage output
DAI D/A converter current output
USB USB interface
 
 

Optional accessories

Model Description
CA372-I/O Cable with FCN connector at one-end 3m
CAAC2P-B3 AC Supply cord 3m
CAAC3P-CEE7/7-B2 AC Supply cord (Voltage resistance:250V)2m
CN34 D-Sub9p connector for RS-232C
CN50 FCN series I/O connector (with cover)
CN51 BCD output connector
CN55 FCN series I/O connector (with diagonal cover)
CN73 D/A converter(3ch) connector
CN90 Waterproof plastic connector for UTMⅡ/UTMV connection
DTC2-PSL Case for TM301
 
 



 Inquiry - TM301 (Torque Monitor)